×

INDI Library v2.0.6 is Released (02 Feb 2024)

Bi-monthly release with minor bug fixes and improvements

Jasem - please read. Polar alignment doesn't work on Windows client.

  • Posts: 910
  • Thank you received: 86
-- Max S
ZWO AM5. RST-135. AZ-GTI. HEQ5. iOptron SkyTracker.
TPO RC6. FRA400. Rokinon 135 and other lenses.
ZWO ASI2600MC. D5500 modified with UVIR clip-in filter.
ZWO ASI120MM Mini x 2. ZWO 30F4 guider. Orion 50mm guider.
ZWO EAF x 2.
4 years 9 months ago #40000

Please Log in or Create an account to join the conversation.

  • Posts: 910
  • Thank you received: 86
Sorry. It doesn't have anything to do with a web browser.
The client runs on Windows 7 64 bit. Server is on RPI which is wire-connected to my home network.

-- Max S
ZWO AM5. RST-135. AZ-GTI. HEQ5. iOptron SkyTracker.
TPO RC6. FRA400. Rokinon 135 and other lenses.
ZWO ASI2600MC. D5500 modified with UVIR clip-in filter.
ZWO ASI120MM Mini x 2. ZWO 30F4 guider. Orion 50mm guider.
ZWO EAF x 2.
4 years 9 months ago #40001

Please Log in or Create an account to join the conversation.

  • Posts: 1067
  • Thank you received: 140

Run this command from the terminal on the Stellarmate and it will load full updated INdI and the GSC files

sudo apt-get install indi-full gsc

Or for just GSC

sudo apt-get install gsc
Last edit: 4 years 9 months ago by AstroNerd.
4 years 9 months ago #40002

Please Log in or Create an account to join the conversation.

  • Posts: 35
  • Thank you received: 1
I did that on StellarMate. It says that "gsc is already the newest version (1.3~ubuntu18.04.1)" - altough I did not installed it manually before (is it meanwhile automatically installed? Or perhaps because I switched to the Beta Channel?).

Anyway, the "problem" why it did not work the first time, was that at FOV I have to manually type in the calculated FOV of the CCD simulator with the primary scope. After I did that, I could click on start and everything works fine. No refreshing problems.
4 years 9 months ago #40019

Please Log in or Create an account to join the conversation.

  • Posts: 910
  • Thank you received: 86
NH - as I reported it works in simulation mode (after cameras are properly assigned) but doesn't with real cameras (at least I couldn't make it work)...
Also it works on RPI/Ubuntu client. The problem only exists for Windows client.
-- Max S
ZWO AM5. RST-135. AZ-GTI. HEQ5. iOptron SkyTracker.
TPO RC6. FRA400. Rokinon 135 and other lenses.
ZWO ASI2600MC. D5500 modified with UVIR clip-in filter.
ZWO ASI120MM Mini x 2. ZWO 30F4 guider. Orion 50mm guider.
ZWO EAF x 2.
4 years 9 months ago #40042

Please Log in or Create an account to join the conversation.

  • Posts: 35
  • Thank you received: 1
Ok, I just saw that you write that it fails with the simulators too. I will test that also as soon as possible. But it maybe take a while, because I am in the next weeks very often not at home and where I live is the wheater normally bad. I think there is no way to test this with the real setup indoors, correct?
4 years 9 months ago #40057

Please Log in or Create an account to join the conversation.

  • Posts: 910
  • Thank you received: 86
NH,
Look. It was failing with the simulators because the cameras were mis-assigned. Once the cameras assigned correctly - the procedure works. With the simulators.
The problem is - it doesn't work with the Windows client. Works with simulators but not with real setup. On Windows client.
Works fine on RPI/Ubuntu client.
And, no, you cannot test it indoors. You need to see/shoot Polaris.
Thanks!
-- Max S
ZWO AM5. RST-135. AZ-GTI. HEQ5. iOptron SkyTracker.
TPO RC6. FRA400. Rokinon 135 and other lenses.
ZWO ASI2600MC. D5500 modified with UVIR clip-in filter.
ZWO ASI120MM Mini x 2. ZWO 30F4 guider. Orion 50mm guider.
ZWO EAF x 2.
Last edit: 4 years 9 months ago by maxthebuilder.
4 years 9 months ago #40080

Please Log in or Create an account to join the conversation.

Time to create page: 0.469 seconds