×
INDI Library v1.8.1 Released (09 Sep 2019)

Monthly maintenance release INDI v1.8.1

Ioptron mount connection support needed

1 month 3 weeks ago
DerPit
Gold Boarder
Gold Boarder
Posts: 264
Karma: 1
More
Ioptron mount connection support needed #44075
The CEM120 needs a different driver (talking Protocol 3.0) than the smaller ones (Protocol 2.5).
So you'd need the indi_ioptronv3_telescope driver. While command sets are quite similar and you likely can connect, especially the get position one is different, which will make operation fail.

openSUSE Tumbleweed KStars git INDI git
GPDX+EQMOD, CEM60EC, ASI1600+EFW+ASI290 mini
The following user(s) said Thank You pug916, wyshyvanuk

Please Log in or Create an account to join the conversation.

1 month 3 weeks ago
wyshyvanuk
Junior Boarder
Junior Boarder
Posts: 21
More
Ioptron mount connection support needed #44078
Alas, unlike the original poster, I have an iOptron IEQ45 GTN, the model just prior to the Pro. It has the RS232 port rather than the USB. I'm using an RS232/USB convertor with what I believe is a Prolific chip. Sorry for causing confusion!!

Please Log in or Create an account to join the conversation.

1 month 3 weeks ago
DerPit
Gold Boarder
Gold Boarder
Posts: 264
Karma: 1
More
Ioptron mount connection support needed #44080
Not sure which INDI version you have, if it is a newer one, you might try the old driver, indi_ieqlegacy_telescope.

openSUSE Tumbleweed KStars git INDI git
GPDX+EQMOD, CEM60EC, ASI1600+EFW+ASI290 mini

Please Log in or Create an account to join the conversation.

1 month 3 weeks ago
wyshyvanuk
Junior Boarder
Junior Boarder
Posts: 21
More
Ioptron mount connection support needed #44083
More info:
1. I've tried choosing all of the available iOptron mounts that looked al all promising, to include iOptron iEQ Legacy, but all result in a Failed to Connect error (2019-09-30T15:48:25: [ERROR] Failed to connect to port (/dev/cu.usbserial). Error: Port failure Error: No such file or directory. Check if device is connected to this port." . Last night, unless I was delirious, I found one that resulted in a Timeout error. I haven't been able to duplicate that this morning.
2. It looks like some of the mount choices result in using the same driver. I'm assuming that this is as it should be.
3. Ports shows /dev.cu.usbserial in both slots, but System Ports shows /dev/cu.Bluetooth-Incoming-Port. If the System Ports slot is clicked/selected, the Ports slot changes to /dev/cu.Bluetooth-Incoming-Port, to match.

I'm totally available to try anything that might clear this issue. Thanks for any advice or insight!!!

I'm at your service

Please Log in or Create an account to join the conversation.

1 month 3 weeks ago
dokeeffe
Platinum Boarder
Platinum Boarder
Posts: 378
More
Ioptron mount connection support needed #44086
Here's a screenshot from my setup. CEM120, plugged into the mount base USB.
One thing to check is the baud rate? Set to 115200
If you need more screenshots let me know. If you are still stuck.... maybe some one of us can teamviewer into your setup?

Celestron CPC1100 Atik 383L
HP8300 Elite i5 running Xubuntu, Indi, Kstars & Ekos
Roll off roof observatory
Battling Irish weather
github.com/dokeeffe
twitter.com/BallyhouraStars
Attachments:

Please Log in or Create an account to join the conversation.

1 month 3 weeks ago
DerPit
Gold Boarder
Gold Boarder
Posts: 264
Karma: 1
More
Ioptron mount connection support needed #44089
Uhm, maybe some splitoff is needed here. The original post from almost half a year ago was about the CEM120, but the current issue of wyshyvanuk is with another model, the IEQ45 GTN. So CEM120 settings do not help :(

@wyshyvanuk: What hand controller do you have? 8406 or 8407? If the former, you should use the HC8406 driver, indi_ioptronHC8406 if the listing on the driver page is correct,.
I seem to remember some note that some driver needs the mount to be star-aligned with the HC before you can use it with INDI - maybe it was this one? Have you tried that, doing a 1/3 star alignment before connecting?

openSUSE Tumbleweed KStars git INDI git
GPDX+EQMOD, CEM60EC, ASI1600+EFW+ASI290 mini

Please Log in or Create an account to join the conversation.

1 month 3 weeks ago
wyshyvanuk
Junior Boarder
Junior Boarder
Posts: 21
More
Ioptron mount connection support needed #44091
I have the 8407. The indication on the driver page is that the INDI ZEQ25 should apply. Choosing this on the Profile Editor results in the correct Name and Exec in the Control Panel. But the mount still fails to connect. The rig is set up in my study. I haven't had the courage to actually take it outdoors yet ;~). Thanks!!!

Please Log in or Create an account to join the conversation.

1 month 3 weeks ago
DerPit
Gold Boarder
Gold Boarder
Posts: 264
Karma: 1
More
Ioptron mount connection support needed #44093
Well, testing things indoors first is always the better choice :)
Just for confirmation - you are using some Stellarmate or similar? Because the port name does look very unfamiliar. Unfortunately I've never used one of those, so I don't know exactly how to handle them.
Does the INDI control panel have the 'Auto Search' enabled (in the Connection tab)? If not maybe have a try with that.

openSUSE Tumbleweed KStars git INDI git
GPDX+EQMOD, CEM60EC, ASI1600+EFW+ASI290 mini

Please Log in or Create an account to join the conversation.

1 month 3 weeks ago
dokeeffe
Platinum Boarder
Platinum Boarder
Posts: 378
More
Ioptron mount connection support needed #44094
soooory, my bad. I didn't realise this thread was that old I thought it was a new thread relating to CEM120 connection problems. Please ignore my message above. Sorry for confusion

Celestron CPC1100 Atik 383L
HP8300 Elite i5 running Xubuntu, Indi, Kstars & Ekos
Roll off roof observatory
Battling Irish weather
github.com/dokeeffe
twitter.com/BallyhouraStars

Please Log in or Create an account to join the conversation.

1 month 3 weeks ago
wyshyvanuk
Junior Boarder
Junior Boarder
Posts: 21
More
Ioptron mount connection support needed #44095
Stellarmate in not being used. I have the elements on the tripod connected directly to my Mac using USB connections and an RS232/USB adaptor. I've flipped back and forth between Auto Search Enabled and Disabled, but it's mostly been on Enabled.
Regards,
Ted

Please Log in or Create an account to join the conversation.

1 month 3 weeks ago
wyshyvanuk
Junior Boarder
Junior Boarder
Posts: 21
More
Ioptron mount connection support needed #44096
The CEM120 (yes, I do want one) issue was my fault entirely. I was led into this post by the RS232 /USB issue.
Ted

Please Log in or Create an account to join the conversation.

1 month 2 weeks ago
wyshyvanuk
Junior Boarder
Junior Boarder
Posts: 21
More
Ioptron mount connection support needed #44129
Progress: I've learned, at long last, that a driver must be installed for the RS232 to USB adaptor. My apologies for dragging you through this quagmire.
1. My adaptor apparently uses a Prolific chip. I downloaded and installed the appropriate driver from Prolific, and, oh my, EKOS recognizes the IEQ45 mount using the ZEQ25 profile.
2. However, the mount is not responding to any "movement" controls from the Mac. The mount WILL move when linked to the 8407 HC.
3. The iOptron website suggests using the FTDI chip on the adaptor. I have ordered an adaptor with that chip. I'm not optimistic, but what the heck.
As always, any insight or advice is welcomed!! Moving the mount would seem to be an integral part of the installation ;~).

Please Log in or Create an account to join the conversation.

Time to create page: 1.080 seconds