Hi,
I need to use this weather station with ascom to, and found this post.
How did you succeed in the conversion?
I don't understand exactly the way to use : export data with a python script, then read it from ascom driver? Wich one?
Can you explain to me how to do this please?

Read More...

adrien created a new topic ' Analyze Tab' in the forum. 2 years ago

Hi
would like to know if there's any way to add weater datas on Analyze Tab ?
this could be a good option to see quickly if bad guide is due to some clouds or wind.
unfortunaly, there is no option in indi panels to add those.

the only way i've found actually is hard and not fun.... : export weather datas (with mqtt) and check guidelog. mix that in influxdb and could have datas..... but maybe (i wish) we can do this easylier ?

Read More...

adrien created a new topic ' profile, scheduler and dome issue' in the forum. 2 years ago

Hi
i met an issue with the scheduler
i want to run a scheduler WITHOUT have to open my roof ( no constraints set).
with my current profile (with aldiroof), if i uncheck unmount dome, roof still opens when scheduler starts.

so i created a new profile, without any dome, and started the schedule. but the roof still opens... :/
it's the same with a dome simulator.

i tried with a total profile with simulators , each time I start a schedule, the roof is opened...


Why is that a real problem ? ^^'
because i managed to restart ekos when weater becomes better , i found a way to force flat frames even if the 1ts schedule is stopped by clouds.
not very clean (mqtt , ssh , node red , sh and ekos controller.py) , but i'm not good at programming ^^'

but that the roof opens whatever the current weather is verry annoying (and dangerous) , and I need to start flat schedule even when it's raining


How can i enforce the roof to be close when i start thoses .esq ?

thx :)

Read More...

adrien created a new topic ' profile, scheduler and dome issue' in the forum. 2 years ago

Hi
i met an issue with the scheduler
i want to run a scheduler WITHOUT have to open my roof ( no constraints set).
with my current profile (with aldiroof), if i uncheck unmount dome, roof still opens when scheduler starts.

so i created a new profile, without any dome, and started the schedule. but the roof still opens... :/
it's the same with a dome simulator.

i tried with a total profile with simulators , each time I start a schedule, the roof is opened...


Why is that a real problem ? ^^'
because i managed to restart ekos when weater becomes better , i found a way to force flat frames even if the 1ts schedule is stopped by clouds.
not very clean (mqtt , ssh , node red , sh and ekos controller.py) , but i'm not good at programming ^^'

but that the roof opens whatever the current weather is verry annoying (and dangerous) , and I need to start flat schedule even when it's raining


How can i enforce the roof to be close when i start thoses .esq ?

thx :)

Read More...

adrien replied to the topic 'profile, scheduler and dome issue' in the forum. 2 years ago

update :

the problem happens with stellarmate (last version , 64bits)

also, i've just met another anoying issue ; if i start a schedule with weather conditons, the scheduler doesn't care about it. it opens the roof, unpark the mount and the cap.
Only after that it checks if weather conditions are ok , then park everything.
i've just tested with stellarmate (pi4 8G) and ekos on ubuntu 20.14 (OK)
so i think i'll have to migrate everything on this PC
the pi could have been a good solution (low consumption) but it's actually unsafe

:/

Read More...

adrien created a new topic ' profile, scheduler and dome issue' in the forum. 2 years ago

Hi
i met an issue with the scheduler
i want to run a scheduler WITHOUT have to open my roof ( no constraints set).
with my current profile (with aldiroof), if i uncheck unmount dome, roof still opens when scheduler starts.

so i created a new profile, without any dome, and started the schedule. but the roof still opens... :/
it's the same with a dome simulator.

i tried with a total profile with simulators , each time I start a schedule, the roof is opened...


Why is that a real problem ? ^^'
because i managed to restart ekos when weater becomes better , i found a way to force flat frames even if the 1ts schedule is stopped by clouds.
not very clean (mqtt , ssh , node red , sh and ekos controller.py) , but i'm not good at programming ^^'

but that the roof opens whatever the current weather is verry annoying (and dangerous) , and I need to start flat schedule even when it's raining


How can i enforce the roof to be close when i start thoses .esq ?

thx :)

Read More...

adrien created a new topic ' profile, scheduler and dome issue' in the forum. 2 years ago

Hi
i met an issue with the scheduler
i want to run a scheduler WITHOUT have to open my roof ( no constraints set).
with my current profile (with aldiroof), if i uncheck unmount dome, roof still opens when scheduler starts.

so i created a new profile, without any dome, and started the schedule. but the roof still opens... :/
it's the same with a dome simulator.

i tried with a total profile with simulators , each time I start a schedule, the roof is opened...


Why is that a real problem ? ^^'
because i managed to restart ekos when weater becomes better , i found a way to force flat frames even if the 1ts schedule is stopped by clouds.
not very clean (mqtt , ssh , node red , sh and ekos controller.py) , but i'm not good at programming ^^'

but that the roof opens whatever the current weather is verry annoying (and dangerous) , and I need to start flat schedule even when it's raining


How can i enforce the roof to be close when i start thoses .esq ?

thx :)

Read More...