I am also under the smoke of Schiphol in Roelofarendsveen and I have also been imaging the Veil Nebula.
Here is my current effort. Still needs a lot of work but I am fairly pleased with the data.
Still waiting for the field flattner. According to Robtics they are available again so I hope I will have it soon.
WO ZS 61
Edgehd 8 with Celestron OAG
Stellarmate on RPi 4
HEQ5 with belt mod and ADM dual saddle
294 mc pro
224 guide cam
Sesto Senso focusser
QHY5II-Mono guide camera
EOS6D - not modified
Here is a photograph of my Indi setup. It consists of:
An OnStep modified Astro-Physics AP400 mount;
An ODROID N2 computer running Ubuntu, KStars, EKOS and Indi server;
A RPI running as a hotspot;
A ZWO ASI1600 camera and Zagyl filter wheel;
A Pegasus Astro DFMC focuser and Power Box;
All this on a home made telescope cart (missing a wheel ) that will allow me to roll it out of the garage and get ready for observing/astrophoto within minutes.
I have a few scopes I swap out depending on my imaging target, but here's what's in the photos below:
AT6RC Telescope with CCDT67 telecompressor at around 914mm focal length.
Moonlite focuser with stepper motor
Orion 60mm Guide Scope
Celestron CGX Mount
Pegasus Ultimate Powerbox V2
RPi4 4GB with aluminum case containing fan and heatsinks
ZWO ASI1600MM-Pro, ZWO Filter Wheel with Astrodon Filters
ZWO ASI290MM Mini Guide camera
My setup. Puny AZ-GTi (but I like it very much) in EQ mode.
UPD: added a second 6Ah battery to feed ZWO cameras separately from RPI.
RPI 3 B+ with ABerry and RPI 4 B (4Gb) with SMate.
Nikon D5500 H-a modified. 180 mm f/2.8 antique Nikon. Tamron AF 28-75mm f/2.8. Rokinon 135mm f/2.
ZWO ASI294MC Pro
ZWO ASI120MC-S on ZWO 30F4 MiniScope.
iOptron SkyTracker Pro.
Before I go through my setup, I just wanna say wow, some of the stuff on here is amazing. Well done everyone!!
This is what I have:
- Losmandy G11
- Stellarvue 80mm F/6 APO
- Atik 383L+
- QHY5II with Orion 50mm guiding scope
- Pegasus focuser
- QHY Polemaster
- Pegasus Ultimate powerbox to juice everything up
I know it's a lot and I know I really need to control the rat's nest of cables. With this I'm able to completely take all my light flats and darks from indoors. I setup the scheduler before it gets too dark, and watch it for a bit to make sure nothing funny happens. I the morning I check the logs then go upstairs to cover everything up. Now if we can get a couple of clear nights....
Indi library 1.8.3
Hi all, just thought I’d share my latest creation to further simplify the number of components in my setup.
So, my current rig requires 3 devices for my imaging session.
1. A computer to run kstars/ekos (I currently use the Asus tinker board)
2. A powered USB hub (because my USB3 cameras suck too much power and the Tinker box would not run them without additional power)
3. Astroberry focuser (running in server mode with a Raspberry Pi 0W) which connects to Asus tinker board via indiserver) to focus.
My mount connects to the Asus Tinker Board via Wifi. Eventhing is controller by remote desk topping.
My latest creation is the "ultimate" single box device which uses the current Raspberry Pi 4 (4G version) computer. It eliminates the Astroberry focuser running in server mode and the powered USB hub. Everything is inside a HighPi Rapsberry Pi 4 enclosure (see
I also installed a cooling fan and heat sinks to keep everything cool. Under full load I'm only seeing temperature of 59 degree C with ambient temp of about 26 degree C.
I have all the wiring for the Astroberry focuser which runs a DRV8825 motor controller connected to the Rpi4 GPIO. I also fitted a 12VDC to 5VDC 5Amp buck converter inside, which powers both the Rpi4 (i soldered the power supply directly to the RPi4 board, do this at your own risk!! see picture) and the Astroberry focuser.
I connect my Astroberry focuser to the motor using RJ12 plug.
And that's it. Everything runs beautifully and I reckon this is the ultimate mobile rig.
Lots of trial and error, mainly error, but in hindsight, it was easy!!!
Takahashi FC100DF imaging scope, Orion 50mm guide scope
Skywatcher HEQ5 Pro via Wifi
ZWO ASI 224MC guiding
DIY Astroberry focuser
Tinker Board (Lbuntu 18.04LTS), Raspberry Pi 4 (Raspbian)
I use C8SE with AVX. Pi4 with Astroberry, and 5GHz router for a faster communication, Celestron SkySync GPS, Shoestring with Motofocus autofocus, OAG with ASI120MM Mini (mono) as a guide camera, Celestron f/6.3 reducer, and Canon T3i as capture camera.
Also, I use Jackery Portable Power Station Explorer 240, 240Wh as the power source with passthrough capability, and finally, an IR IP camera for remote monitoring.
Advanced VX mount
Celestron SkySync GPS
OAG with ASI120MM Mini (mono) guide
Celestron f/6.3 reducer